| The
main strength of these motors are that they are
small and compact. In its shortest design, motor
type GDM 12 N, only 39,5 mm of axial space is
required.
Two motor types are available.
DC Disc Motors
Baumüller DC disc motors are permanent magnet
motors with non-ferrous rotors and barrel commutators.
Consequently, they are low in inertia and highly
dynamic throughout the whole speed range.
Brushless Disc Motors
For applications where DC motors (with
their associated commutator and carbon brushes)
are unsuitable, brushless disc motors are ideal.
The additional electrical control required for
any special applications can also be incorporated
in the motor frame.
GDM 75 - 12 - DC Disc Motors
- Barrel commutator
- Ironless rotor
- Winding as a wire bobbin
- Given sufficient ventilation, and depending
on the type of winding, these motors are
able to provide peak
powers well in excess of their nominal
ratings; even capable of offering full
nominal torques at standstill
without sustaining thermal damage
- The inductance of the armatures is very
low, which is the reason for minimal wear
of carbon brushes. Therefore maintenance
costs can be substantially reduced.
- All of the GDM range permit a high
dynamic performance throughout the whole
speed range. Therefore, they are very
well suited to high transient loadings
i. e. frequent start/stop running modes
- Speed-regulated motor without any
externally mounted electronics
- Reduction in cost of cabling
- No additional installation of sensor
mechanisms, such
as tachogenerators or impulse transmitters/encoders
- Maintenance-free due to brushless
electronic commutation
- Flat construction
|
 |
GDM 75-12 Technical data
| |
GDM
75 Z |
GDM
80 F |
GDM
80 N |
GDM
9 K |
GDM
10 F |
GDM
10 N |
GDM
12 Z |
GDM
12 N |
| PN
[W] |
16 |
44 |
71 |
32 |
100 |
142 |
72 |
147 |
| nM
[min-1] |
3000 |
4200 |
2700 |
3000 |
4800 |
30900 |
3000 |
2000 |
| J
[kgcm2] |
0,5 |
0,7 |
0,7 |
0,6 |
1,2 |
1,2 |
2,1 |
2,7 |
| m0
[Ncm] |
5 |
10 |
25 |
10 |
20 |
45 |
23 |
70 |
|
GDM
75 Z |
GDM
80 F |
GDM
80 N |
GDM
9 K |
GDM
10 F |
GDM
10 N |
GDM
12 Z |
GDM
12 N |
PN
[hp] |
0,02 |
0,06 |
0,10 |
0,04 |
0,13 |
0,19 |
0,10 |
0,20 |
nM
[min-1] |
3000 |
4200 |
2700 |
3000 |
4800 |
30900 |
3000 |
2000 |
J
[lb in2] |
0,17 |
0,24 |
0,24 |
0,21 |
0,41 |
0,41 |
0,72 |
0,92 |
m0
[lbf ft] |
0,04 |
0,07 |
0,18 |
0,07 |
0,15 |
0,33 |
0,17 |
0,52 |
Subject to technical modifications
Technical data for continuous operation at an
environmental temperature of 25°C and with
sufficiently large cooling surface. Insulation
class F, protective system IP 44. Other data and
protective systems on request All motors are also
available with tachometer generator, pulse encoder,
holding brake and gearbox.
GDM 100 - 250 - DC Disc Motors
- Barrel commutator
- Ironless rotor
- Winding as a wire bobbin
- Given sufficient ventilation, and depending
on the type of winding, these motors are able
to provide peak
powers well in excess of their nominal ratings;
even capable of offering full nominal torques
at standstill
without sustaining thermal damage
- The inductance of the armatures is very low,
which is the reason for minimal wear of carbon
brushes. Therefore maintenance costs can be
substantially reduced.
- All of the GDM range permit a high dynamic
performance throughout the whole speed range.
Therefore, they are very well suited to high
transient loadings i. e. frequent start/stop
running modes
- Speed-regulated motor without any
externally mounted electronics
- Reduction in cost of cabling
- No additional installation of sensor mechanisms,
such
as tachogenerators or impulse transmitters/encoders
- Maintenance-free due to brushless
electronic commutation
- Flat construction
GDM 100 - 250 Technical
data
| |
GDM
100 N |
GDM
100 N2 |
GDM
120 F |
GDM
120 N |
GDM
120 N2 |
GDM
140 |
GDM
160 |
GDM
180 N |
GDM
180 N2 |
GDM
250/2 |
GDM
250/3 |
GDM
250/4 |
| PN
[W] |
185
|
250 |
146 |
350 |
550 |
470 |
790 |
1000 |
1400 |
2200 |
3100 |
4500 |
| nM
[min-1] |
3200 |
4000 |
4000 |
3000 |
3500 |
3000 |
3000 |
3000 |
3000 |
3000 |
3000 |
3000 |
| J
[kgcm2] |
1,6 |
1,6 |
2,6 |
3,6 |
3,6 |
5 |
9 |
18 |
18 |
90 |
90 |
110 |
| m0
[Ncm] |
0,55 |
0,60 |
0,35 |
1,1 |
1,5 |
1,5 |
2,5 |
3,2 |
4,5 |
7,0 |
10,0 |
14,5 |
| |
GDM
100 N |
GDM
100 N2 |
GDM
120 F |
GDM
120 N |
GDM
120 N2 |
GDM
140 |
GDM
160 |
GDM
180 N |
GDM
180 N2 |
GDM
250/2 |
GDM
250/3 |
GDM
250/4 |
| PN
[hp] |
0,25
|
0,34 |
0,20 |
0,47 |
0,76 |
0,6 |
1,1 |
1,3 |
1,9 |
3,0 |
4,2 |
6,0 |
| nM
[min-1] |
3200 |
4000 |
4000 |
3000 |
3500 |
3000 |
3000 |
3000 |
3000 |
3000 |
3000 |
3000 |
| J
[lb in2] ] |
0,55 |
0,55 |
0,89 |
1,23 |
1,23 |
2 |
3 |
6 |
6 |
31 |
31 |
38 |
| m0
[lbf ft] |
0,41 |
0,44 |
0,26 |
0,81 |
1,11 |
1,11 |
1,8 |
2,4 |
3,3 |
5,2 |
7,4 |
10,7 |
Subject to technical modifications
Technical data for continuous operation at an
environmental temperature of 25°C and with
sufficiently large cooling surface. Insulation
class F, protective system IP 44. Other data and
protective systems on request All motors are also
available with tachometer generator, pulse encoder,
holding brake and gearbox.
DSM 115 - 190 - Brushless Disc Motors
- Barrel commutator
- Ironless rotor
- Winding as a wire bobbin
- Given sufficient ventilation, and depending
on the type of winding, these motors are able
to provide peak
powers well in excess of their nominal ratings;
even capable of offering full nominal torques
at standstill
without sustaining thermal damage
- The inductance of the armatures is very low,
which is the reason for minimal wear of carbon
brushes. Therefore maintenance costs can be
substantially reduced.
- All of the GDM range permit a high dynamic
performance throughout the whole speed range.
Therefore, they are very well suited to high
transient loadings i. e. frequent start/stop
running modes
- Speed-regulated motor without any
externally mounted electronics
- Reduction in cost of cabling
- No additional installation of sensor mechanisms,
such
as tachogenerators or impulse transmitters/encoders
- Maintenance-free due to brushless
electronic commutation
- Flat construction
Brushless Disc Motors are manufactured
according to two different principles:
For the lower range (motors DSM 115) the principle
of DC disc motor is just reversed. The ironless
winding slips from the rotor into the stator,
the magnets slip from the stator into the rotor
where they can be built in the easiest way just
upon the rotating magnetic feedback. This type
of motor has no cogging effect on principle.
For the higher range (motors DSM 117 –
190) the stator winding will be inserted into
the slotted armature with skewed stacks. The power
output can be increased considerably by means
of the smaller magnetic air gap. The cogging effect
normally existing on this type of motor is nearby
completely compensated by special means.
DSM 115 - 190 Technical data
| |
DSM
115
N/I 1) |
DSM
115
N2) |
DSM
117
N |
DSM
130
N |
DSM
150
N |
DSM
170
N |
DSM
190
N |
DSM
190
N2/L |
| PN
[W] |
205 |
410 |
470 |
1400 |
2260 |
3000 |
4500 |
6300 |
| nM
[min-1] |
3000 |
3000 |
3000 |
3000 |
3000 |
3000 |
3000 |
1000 |
| J
[kgcm2] |
10 |
10 |
10 |
18 |
40 |
60 |
90 |
120 |
| m0
[Ncm] |
0,65 |
1,3 |
1,5 |
4,5 |
7,2 |
9,6 |
14,4 |
60,0 |
| |
DSM
115
N/I 1) |
DSM
115
N2) |
DSM
117
N |
DSM
130
N |
DSM
150
N |
DSM
170
N |
DSM
190
N |
DSM
190
N2/L |
| PN
[hp] |
0,3 |
0,5 |
0,6 |
1,9 |
3,0 |
4,0 |
6,0 |
8,4 |
| nM
[min-1] |
3000 |
3000 |
3000 |
3000 |
3000 |
3000 |
3000 |
1000 |
| J
[lb in2] ] |
3,4 |
3,4 |
3,4 |
6,2 |
13,7 |
20,5 |
30,8 |
41,0 |
| m0
[lbf ft] |
0,5 |
1,0 |
1,1 |
3,3 |
5,3 |
7,1 |
10,5 |
44,3 |
1) ironless disc motor with integrated
electronic
2) ironless disc motor
Subject to technical modifications
Visitor adress:
 |
Baumüller
Nürnberg GmbH
Facility Bad Gandersheim
Flugplatzweg 2
D - 37581 Bad Gandersheim
T: +49 (0) 5382 - 9805 - 0
F: +49 (0) 5382 - 9805 - 55
Email: mail@discmotor.com
www.baumueller.de |
Your contact partner:
How to find us:
 |
AUTO
BAB A7 Aus
Richtung NORDEN
Ausfahrt Seesen
Richtung Bad Gandersheim = B 243 / B 64.
Von B 64 Ausfahrt Bad Gandersheim Gewerbegebiet
Süd/Flugplatz abfahren, nächstmögliche
2 x links abbiegen = Flugplatzweg,
an den Einfahrten vorbei nach 200 m links
in den Kriegerweg.
Aus Richtung SÜDEN
Ausfahrt Echte
Richtung Bad Gandersheim = B 445.
Vor dem "Lorowerk" in den
Kriegerweg rechts abbiegen und Flugplatzweg
überqueren.
BAB A2 Aus
Richtung WESTEN
Ausfahrt Bad Eilsen
Richtung Hameln-Höxter = B 83,
vor Bodenwerder rechts in Richtung Eschershausen
= B 240.
In Eschershausen Richtung Seesen = B 64.
Von B 64 Ausfahrt Bad Gandersheim Gewerbegebiet
Süd/Flugplatz abfahren, links abbiegen
und nächstmögliche rechts = Flugplatzweg,
an den Einfahrten vorbei nach 200m links
in den Kriegerweg.
DEUTSCHE BAHN
Bahnhof Bad Gandersheim mit
dem Taxi ca. 1 km
FLUGZEUG
Privatflugplatz Bad Gandersheim
ca. 500 m
(max. Landegewicht 2000 kg) |
Anfahrtsskizze
ausdrucken 
|
|
